The strong countersunk screw fixing for soft insulating boards

TermoZ CS II DT 110 V

Name: TermoZ CS II DT 110 V
Brand: fischer

The TermoZ CS DT 110V, as a fully pre-assembled ETICS fastener with a plate diameter of 110mm for countersunk mounting, is perfectly suited for fastening insulation boards with low compressive strength. By combining the advantages of countersunk installation and additional plates, a homogeneous surface is achieved with higher pull-through values at the same time. The fastener is installed countersunk perfectly with the CS setting tool and a standard hammer drill or cordless screwdriver.

Product Variant

Download of image data

Product Variant

Approvals / Test reports

18 product variants

Drill diameter

Effect. anchorage depth

Max. usable length at countersunk installation

Min. total drill whole depth incl. insulation at countersunk installation

Drive

Amount

Legend = Permission Available— = Permission not Available

Viewed 18 of 18 variant (s)

Advantages

Pre-assembled fixing with a 110 mm plate for countersunk mounting.
The compound screw minimises thermal bridges, thus there are no anchor marks on the façade.
The combination of the advantages of countersunk installation and additional plates achieves a homogeneous surface with higher pull-through values at the same time.
The very thin plate edge provides an optimal fit to the insulation board and the application of thin reinforcement layers.
Due to the special expansion zone of the anchor sleeve the TermoZ CS II is the first insulation anchor with an approval for hammer-drilled holes in vertically perforated bricks.
The closed plate does not allow dirt to be ejected and thus ensures a clean setting result.
The special geometry of the underside of the plate reduces the necessary insertion torque for convenient and fast installation.

Applications

Countersunk installation of soft insulation materials such as mineral wool boards on concrete and masonry

Building materials

Building material classes A, B, C, D, E
Concrete
Building brick
Solid sand-lime brick
Lightweight concrete
Weather shell
Vertically perforated brick
Perforated sand-lime brick
Hollow blocks made from lightweight concrete
Lightweight aggregate concrete
Aerated concrete

You can find detailed information on building materials in the approval document.

Approval

ETA-14/0372
DoP No. 0298
DoP No. 0346
EPD-FIW-20210314-CBD1-EN

Functionality

Fast countersunk installation with the TermoZ CS setting tool and a standard hammer drill or cordless screwdriver.
The fixing is pushed through the insulation into the drill hole and is screwed in.
The installation is completed when the plate is flush with the insulation board.
After countersunk installation, the anchor plate has to be covered with a round cap.

Installation TermoZ CS II DT 110 V

1 / 6

ETA Certification Document

pdf, ETA-14/0372

European Technical Assessment for fischer TermoZ CS II 8 and fischer TermoZ CS II 8 DT 110 V

Created on 11/03/2023

DOP - Declaration of Performance

pdf, DoP No. 0346

Declaration of Performance for fischer TermoZ CS II 8 / TermoZ CS II 8 DT 110 V (Plastic anchors for use in concrete)

Created on 11/17/2023

DOP - Declaration of Performance

pdf, DoP No. 0298

Declaration of Performance for fischer TermoZ CS II 8 / TermoZ CS II 8 DT 110 V (Plastic fastener for fixing of external thermal insulation composite systems with rendering)

Created on 05/16/2022

EPD - Environmental Product Declaration

pdf, EPD-FIW-20210314-CBD1-EN

Environmental Product Declaration for fischer Insulation fixings

Valid from 02/22/2022
to 02/21/2027

Load Table

pdf,

TermoZ CS II DT 110V - Permissible tension loads for a single anchor for multiple use for non-structural applications.

Marketing Documents

pdf,

TermoZ CS II. ETICS screw fixing.

System components

ETA-approval
Drill diameter ( d₀ )	8 mm
Effect. anchorage depth ( h_ef )	25 mm
Max. usable length at countersunk installation ( t_fix )	90 mm
Min. total drill whole depth incl. insulation at countersunk installation ( h )	145 mm
Drive	TX30
Amount	100 pcs.
GTIN (EAN-Code)	4048962459364

ETA-approval
Drill diameter ( d₀ )	8 mm
Effect. anchorage depth ( h_ef )	25 mm
Max. usable length at countersunk installation ( t_fix )	110 mm
Min. total drill whole depth incl. insulation at countersunk installation ( h )	165 mm
Drive	TX30
Amount	100 pcs.
GTIN (EAN-Code)	4048962420371

ETA-approval
Drill diameter ( d₀ )	8 mm
Effect. anchorage depth ( h_ef )	25 mm
Max. usable length at countersunk installation ( t_fix )	130 mm
Min. total drill whole depth incl. insulation at countersunk installation ( h )	185 mm
Drive	TX30
Amount	100 pcs.
GTIN (EAN-Code)	4048962420388

ETA-approval
Drill diameter ( d₀ )	8 mm
Effect. anchorage depth ( h_ef )	25 mm
Max. usable length at countersunk installation ( t_fix )	150 mm
Min. total drill whole depth incl. insulation at countersunk installation ( h )	205 mm
Drive	TX30
Amount	100 pcs.
GTIN (EAN-Code)	4048962420395

ETA-approval
Drill diameter ( d₀ )	8 mm
Effect. anchorage depth ( h_ef )	25 mm
Max. usable length at countersunk installation ( t_fix )	170 mm
Min. total drill whole depth incl. insulation at countersunk installation ( h )	225 mm
Drive	TX30
Amount	50 pcs.
GTIN (EAN-Code)	4048962420401

TermoZ CS II DT 110 V

Product Variant

Your advantages / Product description

Application and approval

Assembly instruction

Documents for Downloading