Product Category Picture
Application Picture
Application Picture
1   1

TermoZ CS DT 110V

The strong countersunk screw fixing for soft insulating boards

The TermoZ CS DT 110V, as a fully pre-assembled ETICS fastener with a plate diameter of 110mm for countersunk mounting, is perfectly suited for fastening insulation boards with low compressive strength. By combining the advantages of countersunk installation and additional plates, a homogeneous surface is achieved with higher pull-through values at the same time. The fastener is installed countersunk perfectly with the CS setting tool and a standard hammer drill or cordless screwdriver.

Product Description

Advantages
  • Pre-assembled fixing with a 110 mm plate for countersunk mounting.
  • The compound screw minimises thermal bridges, thus there are no anchor marks on the façade.
  • The combination of the advantages of countersunk installation and additional plates achieves a homogeneous surface with higher pull-through values at the same time.
  • The very thin plate edge provides an optimal fit to the insulation board and the application of thin reinforcement layers.
Related to TermoZ CS II DT 110V:
  • Due to the special expansion zone of the anchor sleeve, the TermoZ CS II, is the first insulation anchor with an approval for hammer-drilled holes in vertically perforated bricks.
  • The closed plate does not allow dirt to be ejected and thus ensures a clean setting result.
  • The special geometry of the underside of the plate reduces the necessary insertion torque for convenient and fast installation.

Available Product Variants


15 Product variant (s) found

15 Product variant (s) found

Variant
ETA-approval
Drill diameter

d0

Effect. anchorage depth

hef

Max. usable length at countersunk installation

tfix

8 [mm]

35 [mm]

[mm]

8 [mm]

35 [mm]

90 [mm]

8 [mm]

25 [mm]

110 [mm]

8 [mm]

25 [mm]

130 [mm]

8 [mm]

25 [mm]

150 [mm]

8 [mm]

25 [mm]

170 [mm]

8 [mm]

25 [mm]

190 [mm]

8 [mm]

25 [mm]

210 [mm]

8 [mm]

25 [mm]

230 [mm]

8 [mm]

35 [mm]

250 [mm]

8 [mm]

35 [mm]

270 [mm]

8 [mm]

35 [mm]

290 [mm]

8 [mm]

35 [mm]

310 [mm]

8 [mm]

35 [mm]

330 [mm]

8 [mm]

35 [mm]

350 [mm]

Legend = Permission Available = Permission not Available
Viewed 15 of 15 variant (s)
0

Application and Permission

Applications
  • Countersunk installation of soft insulation materials such as mineral wool boards on concrete and masonry
Building materials
  • Building material classes A, B, C, D, E
  • Concrete
  • Building brick
  • Solid sand-lime brick
  • Lightweight concrete
  • Weather shell
  • Vertically perforated brick
  • Perforated sand-lime brick
  • Hollow blocks made from lightweight concrete
  • Lightweight aggregate concrete
  • Aerated concrete
* You can find detailed information on building materials in the registration document.

Permission

  • ETA-14/0372
  • DoP 0234

Assembly Instruction

Functionality
  • Fast countersunk installation with the TermoZ CS setting tool and a standard hammer drill or cordless screwdriver.
  • The fixing is pushed through the insulation into the drill hole and is screwed in.
  • The installation is completed when the plate is flush with the insulation board.
  • After countersunk installation, the anchor plate has to be covered with a round cap.
Mounting Strip 1 Picture
Mounting Strip 1 Picture
Mounting Strip 1 Picture
Mounting Strip 1 Picture
Mounting Strip 1 Picture
Mounting Strip 1 Picture

Documents for Downloading

Additional Documents

Approvals

Title Type Created Valid Till
ETA Certification Document (PDF, 2 MB) European Technical Assessment for fischer TermoZ CS 8 and fischer TermoZ CS II 8 ETA-14/0372 3/26/2021
DOP - Declaration of Performance (PDF, 2 MB) DoP 0234 4/5/2021

System Components & Related Categories

fe80::2c6f:357:f52e:7cbe%5